Product Description
Chenxing builds the wire duct profile extrusion line that turns PVC dry blend into electrical trunking. Three host sizes cover 100 to 280 kg/h, with one, two or four cavities in the die and a punching station that cuts slots on the run. Send the section drawing and the hourly target, and the offer comes back as one configuration instead of a menu.
A wire duct profile extrusion line makes the U shaped PVC channel that carries cables through walls, control cabinets and machine frames. One cross section, held for the whole shift. The cover has to clip on by hand at the end of the run, so the lip gap and both side walls cannot drift, and that is the whole job.
This is not the same machine as a general PVC profile extrusion line, which is built to change shapes often. A trunking buyer usually orders one or two sizes and runs them for years. The die, the calibration table and the punching head are set once, and after that the line is judged by how little the section moves between the first metre and the ten thousandth.
Six parts make up the line: a conical twin-screw extruder, a vacuum calibration table, a haul-off, a cutter, a stacker, and for duct work, an online groove punching station between the haul-off and the cutter. The host sizes we build are SJSZ51, SJSZ55 and SJSZ65, rated 100 to 280 kg/h depending on cavity count and profile weight.
Everything downstream of the die is sized from the trunking section, not from the machine frame. That is why the same line layout planning for U channel cable profiles works for a 25 mm mini duct and a 100 mm wall duct on the same host.
PVC dry blend goes into the hopper and the conical twin-screw extruder build details start to matter here: full intermeshing screws, deep screw channel, vented barrel. The vent port pulls moisture and volatiles off the melt before the die, which keeps the surface of a grey or white trunking clean without extra drying time in the plant.
Melt leaves the die and enters the vacuum calibration table within a few centimetres. Water sprays from the top, vacuum pulls from the side slots, and the profile is held against a calibrator while it freezes. For a U channel, the outside of the two side walls is calibrated and the inside is set by the calibrator core, so wall thickness and internal width are fixed at the same moment.
Hauling off comes next. Belt haul-off for thin wall mini duct, caterpillar haul-off for heavy 2 mm wall sections, both with frequency control so the pull speed can be trimmed by a few percent while the line is running. Pull too hard and the profile necks down after the calibrator. Pull too soft and the U walls bow out.
Then the punching head. Trunking needs slots, mounting holes or a cut out for the cover latch, and it is cheaper to punch inline than to run a second operation. The punch sits after the haul-off, uses the profile edge as its reference, and can be switched off in one setting when the order is a plain channel without slots. The haul-off cutter and stacker options are chosen in the same conversation, because a saw cutter that lifts with the profile cuts square on thin walls, and a fixed blade does not.
Cutting comes last. Saw or blade, cutting to the length on the packing list, and the stacker lays the lengths flat so the ends do not chip. Length tolerance we hold is normally plus or minus 2 mm on a saw cut.
One detail worth saying out loud: the SJSZ51, SJSZ55 and SJSZ65 hosts all share a 1000 mm centre height. When a plant moves up from a 51/105 to a 65/132 to gain capacity, the calibration table and the haul-off do not need re-shimming or re-alignment on the floor. Only the die and the screw set change. In our workshop we usually quote the bigger host with the existing downstream equipment kept, which saves the buyer a second base frame.
The conveyor style run from hopper to stacker is the same for PVC extrusion run downstream matching, so a plant that already runs pipe can reuse spares and operator habits. If the line is fed from an in-house compound, the dry blend mixing ahead of the trunking die decides how stable the section stays over a long run.
One, two or four cavity dies. Cavity count is the cost lever in this product. A single cavity die is the safe start, a two cavity die is the common choice for 39 mm and 60 mm duct, and a four cavity die is for one size, one colour, high volume work. More cavities mean a wider die head, a wider calibration table and a heavier haul-off, and a four cavity die swap eats half a day in our bay, mostly on centring and lip adjustment.
Imported brand electrical package with frequency speed control. Main motor, inverter, contactor and screw barrel come from imported brand suppliers, adjusted by inverter. We do not mix local and imported parts on the same control cabinet, because the spare part list then gets confusing for the buyer.
Full intermeshing, deep channel twin screws. Good compounding of PVC dry blend, low shear heat, stable output at 38 rpm.
Vented barrel. Moisture and volatiles leave before the die, so no pin holes in the visible face of a white duct.
Online groove punching. Slots and mounting holes punched in line, referenced from the profile edge, switchable off for plain channel orders.
Die change to other profiles. Change the die head and the same line runs PVC window and door profiles, foamed profile, decorative board and multi hole plastic products. Foamed sections need a different screw set, confirmed at enquiry.
Computerized control. Temperature zones, screw speed, haul-off speed and cutter length on one panel, with recipe storage per trunking size.
The die star, the screw set and the calibrator are made for one section family. Buyers who need many shapes usually keep a second screw set on the shelf, and the general PVC profile extrusion line is the better match when shape changes are weekly rather than yearly.
For plants running rigid PVC in other forms, the pipe and profile lines from one workshop page shows how the extruder platform is shared, and the sheet and board extrusion equipment handles the flat product side of the same plant. Thin strip work sits close to duct work in die terms, which is why the narrow strip profile line reference helps when a buyer wants both trunking and label strip from one supplier.
Host parameters, taken from our standard build sheet. Capacity is for PVC dry blend at the stated screw speed, and it moves with cavity count and profile weight.
| Host model | SJSZ51 | SJSZ55 | SJSZ65 |
|---|---|---|---|
| Main motor (kW) | 18.5 | 30 | 37 |
| Screw diameter / ratio (mm) | 51/105 | 55/120 | 65/132 |
| Screw quantity | 2 | 2 | 2 |
| Screw speed (rpm) | 38 | 38 | 38 |
| Torque (N·m) | 6100 | 7200 | 10300 |
| Max capacity (kg/h) | 100-150 | 150-180 | 200-280 |
| Centre height (mm) | 1000 | 1000 | 1000 |
Selection is mostly about section weight per metre and cavity count. A 39 x 19 mm duct at about 0.55 kg/m on a two cavity die pulls roughly double the hourly rate of a single cavity die at the same haul-off speed, so a small host with two cavities can beat a big host with one. For four cavity work on 60 mm and above, take the SJSZ65: at 38 rpm it holds 10300 N·m and reaches the 280 kg/h top of the range only when the dies, the calibration table and the haul-off are all sized for four strands.
Where the source sheet lists a wider capacity band than the host table, treat the host table as the reference and let us size the auxiliary machines for the upper figure at quotation. If capacity is the deciding point, send the section drawing and the hourly target and we will answer with one configuration, not three.
The machine list by category shows the host sizes next to the pipe and sheet lines built on the same platform, and the marble sheet line sharing the same extruder base is a useful reference for how far one screw set can be pushed.
The section is a U channel with two side walls, a base and a lip on each wall where the cover clips. Typical duct work on this line sits between 25 mm and 100 mm in width, with wall thickness from about 1.0 mm to 2.0 mm. Anything outside that band is possible but needs a different die and a different calibrator, confirmed at enquiry.
Cavity choice, in practice:
1 cavity: development work, small orders, first article approval for a new market.
2 cavities: the volume workhorse for 39 mm and 60 mm duct, one die body, two strands, one haul-off.
4 cavities: single size, single colour, long runs. Higher die pressure, a wider calibration table, more attention to melt distribution across the die.
Cover strips are usually run as a separate flat profile on the same line with a different die, because the cover is a flat or slightly curved strip with two legs, and it does not share the calibration table with the channel. Running channel and cover on the same order means two dies and two setup windows, not two lines.
Material range: rigid UPVC is the normal case for electrical trunking. Soft or semi rigid compounds are possible for edge trim and flexible duct, confirmed at enquiry. Colour is set in the compound, not in the die, and a white duct that looks grey after a die change usually means the barrel was not purged long enough.
If the section needs a punched slot pattern, the punch layout follows the drawing and sits on the line after the haul-off. Slots closer than about 15 mm to the cut end need a different punch timing, so send the pattern with the drawing.
Other profile families that come from the same platform have their own pages, which is useful when a buyer compares die cost against cavity count. The corrugated conduit line solutions cover flexible conduit, the single wall corrugated conduit extrusion covers light wall tube, and the double wall corrugated conduit line covers the heavier grade. Rigid round conduit work belongs with the drainage pipe machine range and the ABS pipe extrusion setup, while large bore needs the HDPE pipe line covering 16 to 1600 mm.
Wire duct and cable trunking is the main product, in grey, white and ivory, plain or slotted. The same line, with a die change, also runs PVC window and door profiles, foamed profile, decorative board and multi hole plastic products for wire protection and edge trim. Electrical casing for switchgear panels, machine frame cable channel and under floor duct all use the same section family, so an order can mix sizes without changing the line.
Adjacent demand often sits in the same plant. Buyers who start with trunking usually ask about three layer PE PPR HDPE pipe line equipment later, or about PC light cover profile line and soft PVC reinforced hose line work once the extrusion team is trained.
Scrap handling matters more than buyers expect. Die start up lumps, edge trim and rejects can go through the SMF grinder for lump and reject reclaim and the agglomerator for edge trim, and the recycling loop for plant scrap page explains how much regrind a rigid PVC section tolerates before the surface starts to show.
Delivery terms: Incoterms FOB, EXW, CFR, CIF or CIP, shipment from Shanghai port. Payment by LC, T/T or Western Union. Packing in wooden box, HS code 84772090. Lead time runs 1 to 3 months in the quiet season and 3 to 6 months in the peak season, counted from the confirmed drawing and the deposit. Price is quotation on request, based on host size, cavity count and the downstream length you need.
The quickest way to get a firm number is to send the trunking cross section drawing with wall thickness, cavity count and target hourly output, plus the material based line solutions you already run if it is a plant extension. Our team reads drawings before quoting, so send a trunking cross section drawing and you get one configuration back.
What is the difference between this line and a general profile extrusion line?
The die and the calibration table are built around a fixed U section, and the line carries an online punching station for slots. A general line is set up for frequent die changes and does not include the punch.
How many cavities should I choose?
Start with two for 39 mm and 60 mm duct. One cavity suits development and small orders. Four cavities only make sense when one size and one colour run for months, because the die change and centring cost has to be recovered.
What capacity can I expect at 280 kg/h?
That figure belongs to the SJSZ65 with four cavities, sized downstream. On two cavities the same host runs nearer the middle of the 200-280 band, because the limiting factor becomes haul-off speed and cooling length, not screw torque.
Can the line punch slots and holes inline?
Yes. The punch station works after the haul-off and references the profile edge. It can be switched off for plain channel orders, and the slot pattern follows your drawing.
Can I run window profiles or foamed sections on the same machine?
Change the die head and the line runs PVC window and door profiles, decorative board and multi hole products. Foamed profile needs a different screw set, so tell us at enquiry rather than after delivery.
Which electrical components are used?
Imported brand main motor, inverter, contactor and screw barrel, with inverter speed control. We keep the whole cabinet on one brand family so the spare part list stays short.
What is the warranty?
1 year on mechanical parts. Wear parts such as screws, barrels and calibrator inserts are excluded, and we quote them separately as a spare set with the line.
What is the lead time and payment term?
1 to 3 months in the low season and 3 to 6 months in the peak season. Payment by LC, T/T or Western Union, with Incoterms FOB, EXW, CFR, CIF or CIP.
How do I get a price?
Price is quotation on request. Send the section drawing, wall thickness, cavity count and target output, and the offer comes back with the host model, downstream lengths and packing.
Trade terms, packing details and the spare part list are on the download specification sheets page, and the buyer questions on extrusion equipment page covers points that come up before an order. Older builds and shipment notes are under workshop and shipment updates, and who builds these lines explains the workshop behind the name.
Talk to Nicole
Nicole handles export enquiries for this line. Send the trunking drawing, the cavity count you have in mind and the hourly output, and she will come back with a configuration and a quotation. Email ceo@cxsljx.com, phone or WhatsApp +86 159 5118 7228, Chenxing Machinery Co., China.
Need the full machine listing as it stands today? view more machine details



Laser Marking Machine vs. Ink Transfer Printer: Differences, Applications and Buying GuideIn plastic pipe extrusion and manufacturing, product identification is an essential part of production. Every pipe may need permanent or continuous markings, including the manufacturer's name, product model, sp
Twin-Screw Extruder Technology: Engineering Excellence in Plastic Compounding and ProcessingTwin-screw extrusion technology stands at the forefront of modern plastic processing, offering capabilities that single-screw systems cannot match. These sophisticated machines deliver superior mixing perform
Introduction: Why Accurate Liquid Dosing Matters in PVC ProductionIn modern PVC processing and plastic compounding, formulation precision directly determines product quality, stability, and production efficiency. Whether manufacturing PVC pipes, profiles, sheets, or granules, liquid additives such a
Extrusion can be a manufacturing method by which the vinyl material is then melted and molded into a profile. Extrusion can provide such things as weatherproofing, piping, fencing, deck railings, window frame pictures and cladding coatings, and cable insulation.The following process is started by co
Over 60% of US manufacturers are adopting digital controls. Discover how IoT-enabled smart dosing systems with real-time monitoring, AI analytics, and predictive maintenance are transforming Industry 4.0 plastic manufacturing.How IoT-Enabled Dosing Systems Are Redefining Smart ManufacturingIndustry
Upgrade your extrusion line with a 16-zone single screw extruder control system for higher precision, stability, and production efficiency.
Introduction: Why 3D Filament Extrusion Lines Matter in Additive ManufacturingWith the rapid growth of additive manufacturing, the demand for stable, high-precision filament materials has increased dramatically. Whether used in industrial prototyping, education, consumer products, or engineering par
Quick Answer The global plastic pipe market is worth roughly USD 90.1 billion in 2026 and is growing at about 5.4% per year through 2034 (Fortune Business Insights).The fastest-growing sub-segment is data center cooling pipe, sized at USD 2.06 billion in 2026 and forecast to reach USD 6.53 billion b
If you’re involved in plastic manufacturing, you've likely encountered the term “extrusion die.” But what exactly is an extrusion die, and how does it function? In this post, we’ll break down the essential elements of extrusion dies and explain how they contribute to the production of high-quality p
Your Ultimate Guide to PVC Mixing EquipmentPVC compounding mixers are indispensable in modern plastic manufacturing, enabling precise blending of raw materials like PVC resin, stabilizers, plasticizers, and additives. These machines ensure uniformity, quality, and efficiency in producing PVC-based p
High-speed mixers play an important role in plastic compounding by blending polymers, additives, fillers and pigments into a uniform mixture. In PVC processing, high-speed hot mixers use mechanical shear and frictional heating to promote material dispersion and prepare PVC dry blends for extrusion a
When planning to invest in a single wall corrugated pipe production line, one important question often comes up: Should you choose a high-speed machine or a low-speed model?Both types of machines can produce single wall corrugated pipes, which are widely used in electrical cable protection, automoti
With building materials evolving rapidly, PVC wall panels have emerged as a go-to solution for interior finishing across residential, commercial, and industrial spaces. Their water resistance, low maintenance, and decorative versatility make them suitable for bathrooms, kitchens, and public environm
The cost of setting up a PVC pipe production line depends on production capacity, pipe diameter range, automation level, and auxiliary equipment.A small PVC pipe production line may cost between $30,000 and $80,000, while a fully automatic high-output line can exceed $300,000.Key equipment includes:
Title: Meta Description: Zhangjiagang Chenxing Machinery Co., Ltd. successfully ships a high-efficiency PE PP waste washing and recycling line to Russia, marking another milestone in their international expansion.Zhangjiagang Chenxing Machinery Co., Ltd. Ships PE PP Waste Washing and Recycling Line
In modern plastic recycling and waste reduction systems, shredding is the first and most critical stage of material size reduction. Whether you are processing plastic lumps, pipes, films, woven bags, pallets, or industrial scrap, choosing the correct shredder type directly affects downstream crushin
Explore the engineering principles of 3D filament extrusion lines. Learn how polymer science, precision mechanics, and IoT integration enable production of high-tolerance filaments for industrial 3D printing.
Introduction: Why Twin Screw Extruders Are Essential for PVC ProcessingIn modern plastic extrusion manufacturing, twin screw extruders are widely recognized as the most reliable solution for processing difficult-to-melt materials such as PVC powder and high-filled compound formulations.Compared with
Just as cars require regular maintenance, your factory’s plastic pipe extrusion system, particularly the single screw extruder, also needs diligent servicing. Proper daily maintenance not only minimizes the risk of equipment failure but also extends the lifespan of your plastic pipe extrusion operat

