Product Description
A plastic strand pelletizer is a granule cutting machine that turns cooled polymer strands into uniform pellets right after an extrusion or recycling line. The strands enter the nip of two rubber feed rollers, the rollers pull them into a cutting head at line speed, and a rotating blade bank with 24 blades cuts them against a fixed bed knife. Standard granule size is 3x3 mm, the recommended strand count is 10 to 30, and output runs about 300 to 600 kg/h depending on motor power. Figures are typical industry reference values, confirmed at enquiry.
Chenxing Machinery supplies the plastic strand pelletizer as the cutting station that finishes a pelletizing line. It takes strands that have already been cooled and sized, and it turns them into granules that can be packed, blended or shipped. The machine suits glass fiber filled compounds, reinforced plastics, PA, PP, PE, PS and ABS, and it handles fibre strand cutting or other line cutting duties.
The unit is a compact cutting cell with a clear job list:
A rubber roller feed nip pulls the strands in without slip, matched to the upstream towing speed.
A rotating blade bank carries 24 blades and cuts against a fixed bed knife.
A blade gap adjustment system works in 0.1 mm steps so the cut length stays tight.
A discharge chute drops the granules to a conveyor, packing station or air conveying line.
A safety guard covers the blade area and interlocks with the drive.
An optional air conveying unit blows the granules to the next process stage.
The blade gap is the first thing to set on a new material. Too tight and the blades kiss the bed knife; too loose and the granule tail feathers. Operators check the gap in 0.1 mm steps and sharpen the blade bank on a set interval, usually tied to output tonnage.
The cutting cycle is fixed. Cooled strands from the water bath or from a die face enter the nip of two rubber rollers, the rollers feed the strands at line speed into the cutting head, and the rotating blade bank cuts 3x3 mm granules against a fixed bed knife. The granules drop through the discharge chute to a conveying or packing stage.
Cut length stays stable because the rollers and the blade bank run from the same speed control. Slip coupling or a frequency inverter sets the towing speed, and the operator matches it to the extruder output so the strand never sags between the cooling bath and the nip. Rubber roller pressure is set once per strand bundle size, and the roller durometer decides how hard the nip can pull without flattening a soft strand.
The table below lists typical industry reference values for two common output tiers. Competitor model names are not used, and every figure is confirmed at enquiry.
| Item | Typical industry reference |
|---|---|
| Frame style | Cantilever or gantry |
| Motor power | 4 kW tier or 7.5 kW tier |
| Speed control | Slip coupling or frequency inverter |
| Strand number | Up to 16 strands (4 kW tier) or up to 28 strands (7.5 kW tier) |
| Max towing speed | About 72 m/min |
| Granule size | 3x3 mm standard, other sizes on request |
| Max output | Up to 300 kg/h (4 kW tier) or up to 500 kg/h (7.5 kW tier) |
| Rotary blade dia x length | About 150x150 mm (4 kW tier) or 150x200 mm (7.5 kW tier) |
| Blade count | About 24 |
| Rubber roller dia x length | About 70x150 mm (4 kW tier) or 70x200 mm (7.5 kW tier) |
| Material hardness | Cuts products with hardness above about 35 Shore |
| Power supply | 380V 50Hz 3 phase standard, other voltages on request |
| Certification | CE, ISO9001 |
All values above are typical industry reference figures, confirmed at enquiry. The actual output and strand count are matched to the upstream line and the target granule size of each plant.
The frame decides how the machine handles blade access and strand loading. A cantilever frame holds the cutting head on one side, which leaves the feed side open and makes strand threading quick; a gantry frame carries the head across the full width, which suits wider strand bundles and heavier blade banks. Both frames use the same cutting geometry: 24 rotary blades sweeping past a fixed bed knife.
The blade material is wear resistant and the blade bank is sharpened on a set interval. On glass fiber filled compounds the abrasive fill wears the edge faster, so the interval shortens and the gap check becomes part of the shift routine. Rubber rollers wear too, and the durometer and surface grip are checked when strand feed starts to slip.
The strand pelletizer sits at the end of pelletizing lines that make granules from glass fiber filled compounds, reinforced plastics, PA, PP, PE, PS and ABS. It also cuts fibre strands and handles other line cutting duties where a continuous strand needs to become a uniform granule.
The typical arrangement is simple. The extruder pushes the melt through a die face or a strand die, the strands pass through a water bath for cooling, and the pelletizer cuts them at the bath exit. That layout appears on a complete pelletizing line, on a recycling line solution for reclaimed material, and on a two stage recycling machinery setup where the first stage densifies and the second stage cuts.
The machine also fits into existing lines as a retrofit. A plant that already runs an extruder and a water bath can add the pelletizer at the bath exit, and the speed control ties into the line controller or runs standalone. For reclaimed material, the cutter pairs with a washing recycling line or a PET bottle washing station, so the cutting duty stays the same while the feed comes from cleaned flakes. The same cutting cell is used beside board sheet line edge trim duty, and the wider extruder range pages show how the upstream machine is sized.
Customization is available where it changes the fit of the cutting station. The fixed part is the cutting principle: two rubber rollers feed strands into a rotating blade bank that cuts against a bed knife.
| Customizable | Fixed |
|---|---|
| Motor power tier: 4 kW or 7.5 kW | Strand feeding by rubber roller nip |
| Slip coupling or frequency inverter speed control | Rotary blade bank cutting against a bed knife |
| Strand count range up to 16 or up to 28 | Granule discharge through a chute |
| Granule size via blade spacing and bed knife position | 24 blade cutting geometry |
| Stainless contact parts for clean room or food duty | Cutting station, not a compounding unit |
| Voltage, frequency and phase | The upstream extruder and cooling bath are separate |
| Cantilever or gantry frame |
The granule size is changed by blade spacing and the bed knife position, and the standard 3x3 mm is only a starting point. Other sizes are on request, confirmed at enquiry, because the blade count and the roller speed are tuned together.
Chenxing Machinery has run ISO9001 quality management since 2002, and CE certification applies to the machine series. The factory has built plastic machinery for more than 20 years, and the strand pelletizer goes through the same run-out checks as the rest of the range, from dry blend preparation units to the compounding solution packages, including the mixer station used upstream of the extruder and the ancillary equipment that surrounds the line.
Each cutting head is checked before shipment. The blade bank run-out is measured, the nip roller alignment is set against the bed knife, and the machine runs a trial cutting pass with a sample strand bundle so the granule length and the surface are confirmed. The blade gap is recorded on the test sheet, and the rubber roller durometer is noted for the customer record.
The package includes the inspection report and the certificate of conformity, plus a 1 year warranty on the machine. The factory history page shows the workshop and the testing routine behind the brand.
The minimum order is 1 unit, and the lead time follows the motor tier and the optional extras, confirmed on the order. Export packing uses stretch film and wooden pallets, with the cutting head, motor and control panel separated and braced so the blades and the rollers are not damaged in transit. Machine data sheets are packed with each unit, and the setup notes cover the blade gap, the roller pressure and the speed matching.
Trade terms cover FOB, EXW, CFR, CIF and CIP, and payment is by T/T or L/C. The destination port is needed at quotation stage so the freight and packing plan can be sized correctly.
A plastic strand pelletizer is a granule cutting machine that turns cooled polymer strands into uniform pellets. Two rubber rollers feed the strands into a cutting head, and a rotating blade bank cuts them against a fixed bed knife.
It suits glass fiber filled compounds, reinforced plastics, PA, PP, PE, PS and ABS, and it handles fibre strand cutting or other line cutting duties. It cuts products with hardness above about 35 Shore.
The standard granule size is 3x3 mm. Other sizes are on request, set by blade spacing and the bed knife position, confirmed at enquiry.
The recommended strand count is 10 to 30. The lower output tier handles up to 16 strands and the higher tier up to 28 strands, typical industry reference values.
Output runs about 300 to 600 kg/h depending on motor power. The 4 kW tier reaches up to 300 kg/h and the 7.5 kW tier up to 500 kg/h, confirmed at enquiry.
The rollers and the blade bank run from the same speed control, slip coupling or frequency inverter. The operator matches the towing speed to the extruder output so the strand stays tight through the nip.
Yes, in the standard layout. The strands pass through a water bath for cooling before they enter the nip, and the towing speed matches the cooling time for the strand diameter.
Yes. The pelletizer works as a retrofit at the exit of an existing extruder and water bath, and the speed control ties into the line controller or runs standalone.
The blade bank is sharpened on a set interval, and the blade gap is checked in 0.1 mm steps. Rubber rollers wear and are replaced when strand feed starts to slip.
Browse the machine portfolio and the line solution planning pages, and check the pelletizer FAQ for more granule cutting questions.
Send the following information so the strand pelletizer can be quoted and sized correctly:
Polymer type and compound recipe, including filler content
Strand count and strand diameter
Target output in kg/h
Granule size required
Existing line layout: extruder type, water bath length, line speed
Frame style preference: cantilever or gantry
Voltage, frequency and phase
Destination port and preferred trade terms
For related cutting and recycling equipment, browse the agglomeration unit, the SMF grinding machine, the film washing line and the continuous suction machine pages. To move forward with a quotation, ask Chenxing for a cutting trial with the list above. view more machine details
Nicole | Email: ceo@cxsljx.com | Tel WhatsApp WeChat: +86 159 5118 7228



Explore the engineering principles of 3D filament extrusion lines. Learn how polymer science, precision mechanics, and IoT integration enable production of high-tolerance filaments for industrial 3D printing.
Introduction: Why Twin Screw Extruders Are Essential for PVC ProcessingIn modern plastic extrusion manufacturing, twin screw extruders are widely recognized as the most reliable solution for processing difficult-to-melt materials such as PVC powder and high-filled compound formulations.Compared with
Just as cars require regular maintenance, your factory’s plastic pipe extrusion system, particularly the single screw extruder, also needs diligent servicing. Proper daily maintenance not only minimizes the risk of equipment failure but also extends the lifespan of your plastic pipe extrusion operat
Over 60% of US manufacturers are adopting digital controls. Discover how IoT-enabled smart dosing systems with real-time monitoring, AI analytics, and predictive maintenance are transforming Industry 4.0 plastic manufacturing.How IoT-Enabled Dosing Systems Are Redefining Smart ManufacturingIndustry
Introduction: Understanding the Role of ABS Pipe Production in Today’s IndustryIn plumbing, electrical infrastructure, and industrial ventilation systems, ABS pipes have earned their place thanks to their strength, impact resistance, and stability in diverse environments. But these pipes don’t come
The Comprehensive Guide to Plastic Granulator Machine Technology and Market TrendsThe plastic granulator machine market represents one of the most dynamic segments within the broader plastic processing equipment industry. These essential machines transform plastic waste streams into uniform granules
Plastic pipes are an essential part of many industries, from construction to plumbing, and they are used for everything from water supply to drainage systems. Understanding the process of plastic pipe manufacturing can give you a deeper appreciation of the technology involved. In this article, we wi
Introduction: Why Single Screw Extruders Remain the Backbone of Plastic ProcessingDespite the rapid development of twin screw and special extrusion systems, the single screw extruder remains the most widely used plastic processing machine in the global extrusion industry.From pipe extrusion and prof
In modern elevator systems, safety, balance, and smooth operation are critical factors. While most people are familiar with elevator cabins and counterweights, fewer understand the importance of a component called the elevator compensation chain.This seemingly simple mechanical element plays a vital
Introduction: Why 3D Filament Extrusion Lines Matter in Additive ManufacturingWith the rapid growth of additive manufacturing, the demand for stable, high-precision filament materials has increased dramatically. Whether used in industrial prototyping, education, consumer products, or engineering par
Maintaining plastic extrusion equipment is crucial for ensuring the efficiency and longevity of your production line. Proper maintenance not only reduces downtime but also extends the life of machines such as pipe extrusion machines, PVC extrusion machines, and HDPE pipe extrusion systems. Below are
Discover Chenxing's advanced PVC pipe extrusion lines with 25% energy savings, ISO-certified quality, and global technical support. Get a free quote for customized solutions!
Twin-Screw Extruder Technology: Engineering Excellence in Plastic Compounding and ProcessingTwin-screw extrusion technology stands at the forefront of modern plastic processing, offering capabilities that single-screw systems cannot match. These sophisticated machines deliver superior mixing perform
Twin-screw extruder is a kind of extruder which is developed on the basis of the single-screw extruder and has some connection with a single-screw extruder, but there are many differences. This article will introduce a twin-screw extruder in detail. Here is the list of contentsBackground of the birt
Discover Chenxing's advanced PVC pipe extrusion technology with 25% energy savings. Learn about CE-certified extrusion lines, customizable parameters, and global support. Get a free quote!
Your Ultimate Guide to PVC Mixing EquipmentPVC compounding mixers are indispensable in modern plastic manufacturing, enabling precise blending of raw materials like PVC resin, stabilizers, plasticizers, and additives. These machines ensure uniformity, quality, and efficiency in producing PVC-based p
The Essential Air Separation Equipment in PET Bottle Recycling LinesAs the global recycling industry moves toward higher-quality recycled plastics, efficient material separation has become one of the most important steps in modern recycling systems. In PET bottle recycling, one major challenge is se
Introduction: Why Agglomerators Are Essential in Modern Plastic RecyclingIn plastic recycling plants, one of the biggest challenges is handling lightweight, thin, and low bulk density materials such as PE film, PP woven bags, raffia, agricultural film, and soft plastic scraps.A plastic agglomerator,
The cost of setting up a PVC pipe production line depends on production capacity, pipe diameter range, automation level, and auxiliary equipment.A small PVC pipe production line may cost between $30,000 and $80,000, while a fully automatic high-output line can exceed $300,000.Key equipment includes:

