The Plastic Film Screw Press Squeezer and Densifier is designed for dewatering and densifying washed plastic films in plastic recycling operations. It is suitable for processing lightweight materials such as PE films, PP woven bags, agricultural films and non-woven fabrics.
After washing, plastic films usually retain a considerable amount of water. Their low bulk density and flexible structure can also make transportation, storage and feeding into downstream equipment difficult.
This system combines screw press dewatering with a densification process to remove a significant portion of the residual water and increase the bulk density of the processed material. The resulting densified material is easier to convey and feed into subsequent extrusion and pelletizing equipment.
Chenxing provides different machine configurations according to material characteristics, processing capacity and downstream production requirements.
The screw press squeezer and densifier is mainly used in the post-washing section of plastic film recycling lines.
Typical processing materials include:
PE Plastic Film: Washed polyethylene film from industrial and post-consumer recycling streams.
PP Woven Bags: Cleaned polypropylene woven bags after shredding and washing.
Agricultural Film: Washed agricultural films, subject to material condition and equipment configuration.
Non-Woven Fabrics: Suitable non-woven plastic materials, depending on their composition and structure.
Other Lightweight Plastic Films: Customized processing solutions can be evaluated according to the actual material.
The suitability of different materials should be confirmed through sample testing before final equipment selection.
The system combines mechanical squeezing and material densification to prepare washed plastic films for subsequent processing.
Washed plastic films or other suitable lightweight plastic materials are conveyed into the machine through the feeding section.
A stable feeding arrangement helps maintain continuous operation and consistent material flow.
Inside the screw press section, the rotating screw conveys and compresses the material.
Mechanical pressure forces a substantial portion of the retained water out of the plastic film. The separated water is discharged through the machine's drainage structure.
This mechanical dewatering stage reduces the amount of water carried into the downstream densification process.
The compressed plastic material undergoes a densification process. Mechanical friction and controlled processing conditions help soften and compact the lightweight material.
The material becomes denser and more suitable for conveying and feeding into downstream equipment.
The actual densification mechanism and temperature-control arrangement depend on the machine configuration.
The densified plastic material is discharged from the machine for transfer to a storage system, extruder or pelletizing line.
The final material form depends on the processed polymer, machine settings and equipment design.
The screw press applies mechanical compression to washed plastic films, removing a substantial portion of the retained water before further processing.
Plastic films and woven bags are lightweight and bulky. Densification helps reduce their loose volume and improves material handling.
The denser material is generally easier to convey and feed into suitable extrusion and pelletizing systems than loose washed film.
The system can be installed after the washing and initial dewatering stages of a PE/PP film recycling line.
Different machine configurations can be evaluated according to the type of plastic material, required throughput and downstream equipment.
The following table presents the model information currently listed for the CX series. Please confirm all dimensions, parameter definitions and electrical specifications before publication or quotation.
| Parameter | CX-500 | CX-1000 |
|---|---|---|
| Machine Model | CX-500 | CX-1000 |
| Main Motor Power | 90 kW | 160 kW |
| Screw Speed | 42 r/min* | 42 r/min* |
| Processing Capacity | 500–600 kg/h* | 700–800 kg/h* |
| Hydraulic Station Motor | 1.5–2.2 kW | 1.5–2.2 kW |
| Machine Dimensions | To be confirmed | To be confirmed |
| Feeding Inlet Dimensions | To be confirmed | To be confirmed |
| Water Discharge | Bottom drainage | Bottom drainage |
| Material Discharge | Free-falling discharge | Free-falling discharge |
The listed speed and processing capacity should be verified under the specified material and operating conditions. Final throughput depends on material properties, moisture level and machine configuration.
The screw press squeezer and densifier is typically installed in the downstream section of a plastic film washing line.
A typical process arrangement may include:
Belt Conveyor
Plastic Film Shredder or Crusher
Friction Washer
Floating Washing Tank
Screw or Centrifugal Dewatering Equipment, where required
Screw Press Squeezer and Densifier
Material Conveying and Storage
Plastic Extrusion and Pelletizing Equipment
The actual process layout depends on the incoming material, contamination level, required final moisture content and pelletizing requirements.
For applications requiring further moisture reduction, an additional drying stage may be evaluated.
Before choosing a screw press squeezer and densifier, buyers should consider the following factors:
Material Type
Specify whether the material is PE film, PP woven bags, agricultural film, non-woven fabric or a mixed plastic stream.
Initial Moisture Content
Provide the moisture level after the washing and preliminary dewatering stages. This information helps determine the required dewatering configuration.
Required Processing Capacity
The target throughput should be specified in kg/h. Actual capacity needs to be evaluated using representative material samples.
Downstream Equipment
The required material condition depends on whether the densified output will be fed into a storage system, single-stage extruder, two-stage pelletizing line or another processing machine.
Available Installation Space
The machine layout, feeding conveyor, drainage system and discharge arrangement should be considered during project planning.
It is designed for suitable washed lightweight plastic materials, including PE films, PP woven bags, agricultural films and non-woven fabrics. Material compatibility should be confirmed according to the actual composition and condition.
The moisture reduction depends on the initial moisture content, material characteristics, processing capacity and operating conditions. A specific final moisture value should be confirmed through material testing.
The machine produces densified plastic material. Its shape, size and bulk density depend on the material and machine configuration. It should not automatically be described as finished plastic pellets.
The two machines use different dewatering principles. A screw press applies mechanical compression, while a centrifugal dewatering machine uses centrifugal force. They may serve different positions in a recycling line and can be selected or combined according to process requirements.
Yes. The densified material can be conveyed to suitable downstream extrusion and pelletizing equipment. The feeding arrangement should be evaluated according to the extruder design and material characteristics.
Machine configuration and processing capacity can be evaluated according to the material type, required throughput, installation space and downstream process.
Looking for a screw press squeezer and densifier for your PE film recycling line or PP woven bag washing project?
Send us your material type, initial moisture content, target processing capacity and downstream equipment information. Our engineering team can evaluate a suitable configuration for your recycling process.
Contact Chenxing Machinery for technical consultation and a customized quotation.